ca:[1][Changing the Adaptation’s Model Name will make existing Library Entries incompatible. Are you sure?][Cancel|OK]
ae:[2][There is already an Adaptation with this Name (at least Filename).][Cancel]
d1:[3][At least one Driver must remain.][Cancel]
t6:[1][Only 256 Entry Types are possible.][Cancel]
tu:[3][This Entry Type is used by a Driver or a conversion table. So it cannot be deleted.][Cancel]
i3:[1][Only 32768 Items are possible for one Adaptation.][Cancel]
la:[3][Lookahead too large.][Cancel]
hs:[2|Roland Handshake Communication Error][^0 ^1.][OK]
os:[3|Edit String][New String / MIDI String does not fit in object|(maximum size: 64 KB)][Cancel]
pm:[1][If you want to edit Adaptations or create new ones, you can order a Programming Manual from EMAGIC or your local distributor for a nominal fee.][OK]
p1:[3][More than one Loop Start.][OK]
p2:[3][Loop Start without Loop End.][OK]
p3:[3][No SIN or BNK within Loop.][OK]
p4:[3][No Loop Start before Loop End.][OK]
p5:[3][A Roland address was processed which could not be found in the address mapping of data type “^0”.][OK]
p6:[3][The data size defined in data type “^0” is too small for the address mapping table.][OK]
p7:[3][Tried to map an entry offset to a Roland address, but the address mapping table of data type “^0” is too short.][OK]
p8:[3][Found an Address Mapping Table entry in data type “^0” with Repeat > 1, but the Distance parameter is undefined.][OK]
p9:[2][Found an Address Mapping Table entry in data type “^0” with size 0.][OK]
ft:Universal Module Adaptation
gl:Getting Adaptation List...
co:Converting POLYFRAME Adaptation ...
na:### New Adaptation ###
m1: &Adaptation
m2: &Edit Adaptation...|aE
m3: &Save Adaptation|aS
va:variable
y1:auto
y2:left-aligned with
y3:right-aligned with
y4:to the right of
y5:top-aligned with
y6:bottom-aligned with
y7:under
r1:Roland Protocol
x1:enabled
x0:disabled
dp:Show Device ID +
is:is
ig:ignored
re:recognized
a1: New Data Type
a2: New Bank Driver
a3: New Conversion Table
a4: &Save|aS
a5: Export Names...
a6: Add Address Mapping Table
xp:Adaptation name:\ Supports:\ Release:\ Author:\ ---------------------------------------------------------------------- Installation Scan MIDI SysEx Communication Error Device Parameter box Memory Manager Credits Helpfile by
st:Note Off Note On Poly Pressure Control Change Program Change Channel Pressure Pitch Bend System Exclusive (SysEx) End of Exclusive (EOX)
ch:, Channel
vc:, variable Channel
ps:Reset to bank beginning Skip bytes Fractional Dump Stored Data Size Transmitted Data Size Loop Start Loop End Pause Sum up from here Checksum Entry Number in Bank Bank Dump Data Single Dump Data
op:Memory containing value Parameter value
rc:* Mute Channel All Sound Off Reset All Controllers Local Control All Notes Off Omni Mode Off Omni Mode On Mono Mode On (Poly Mode Off) Poly Mode On (Mono Mode Off)
ma:Manufacturer:
di:(Device ID)
bi:Binary:
nA:BANK NUMBERING
nB:Digit / Zero
nC:Divisor
nD:Leading Zero
nE:H/V TITLE
nF:First
nG:No.
nH:Step width
gA:GLOBAL DATA
gB:Manufacturer
gC:Model name
gD:Device ID
gE:Icon
gF:Input Status Enable
gG:Default Timeout
gH:Default Send Pause
gI:Default Play Delay
gJ:Author
gK:DEVICE SCAN
gL:Thru Channel = Device ID
gM:Roland Model
gN:DATA TYPES
gO:BANK DRIVERS
gP:CONVERSION TABLES
gQ:Card Names
gR:GLOBAL MIDI STRINGS
gs: ** Global MIDI Strings INITIALIZATION FAILURE RESPONSE (NAK)
ds: ** Driver Strings Bank Dump Single Dump Bank Request Single Request Before Request / Dump After Dump Default Names Outgoing Bank Dump (optional) Outgoing Single Dump (optional)
tA:Source Adaptation
tB:Source Type
nl:(not installed)
tC:Dest. Type
tD:Source bit 0
tE:Dest. bit 0
tF:Number of bytes
tG:Value
tH:Offset
tN:[3|Error in Conversion Table][Loops can be nested only in 32 levels.][Cancel]
tO:[3|Error in Conversion Table][Too many loop ends.][Cancel]
tP:[3|Error in Conversion Table][Destination offset outside valid limits.][Cancel]
pf: 7 Bit HL: -DCBA987 -6543210 7 Bit LH: -6543210 -DCBA987 4 Bit HL: ----7654 ----3210 4 Bit LH: ----3210 ----7654 Ensoniq EPS Alesis Quadraverb 7 Bit Controller: 0..127 14 Bit Controller: 0..16363 7 Bit Contr., integer steps 14 Bit Contr, integer steps ASCII Hex HL ASCII Hex LH" ASCII Decimal ASCII Dec., 0-terminated 1+7 Bit HL: F E..8 7 6..0 1+7 Bit LH: 7 6..0 F E..8 Sequential:-7654--- ----3210
e#:REQ DUMP SELECT INC
rh: One Way Handshake
al:Aligned
nr:No Request
rO:ROLAND
aR:ADDRESS
ba:Base
pS:Packet Size
tM:Transfer Mode
tc:Thru Channel
ud:user-defined
mu:multiple
of:OFFS HEX DEC ASC
mI:MIN MAX
og:OFFS
m=:===MINIMUM===
m-:===MAXIMUM===
hD:HEX DEC BINARY
fl:FAMILY LSB
fm:FAMILY MSB
ml:MEMBER LSB
mm:MEMBER MSB
ox:Cut Objects
ov:Paste Objects
oc:Clear Objects
ob: &Binary View|aD
oo: Open &Object Editor|aO
sn: &Snap to Grid
ot: &Flatten
sg: &Grid Snap|aG
so: O&bject Snap|aB
mt:Mapped to Roland Address Offset
le: &Layout Mode|aL
on:New Object
om:Moving Objects
oS:Sizing Objects
lM:LAYOUT MODE
gS:Preserve Thru Port/Ch
pT:Preserve MIDI Thru Port/Ch:
cu:[2][This Card button is still used by bank “^0”. First disable this card button in the bank. Then you can delete this card name.][OK]
r2:Wait Send Pause before Request
q1:[1][Adaptation file “^0” does not have the ending “.ADA”, however there already is an Adaptation “^1”. You should delete file “^0”.][No more messages|OK]
q2:[1][Adaptation file “^0” does not have the ending “.ADA”. You should rename it to “^1”.][No more messages|OK]
